We deliver your order as usual, of course with the necessary precautions | more information

BR Drawrein Blackpool

The ends of this drawrein are made of nylon cord (8 mm wide).

Expected delivery time 1-8 working days
£48.95

BR Drawrein Blackpool

The ends of this drawrein are made of nylon cord (8 mm wide). The advantage of cord is that it slides more easily through the bit guards. The rein sections are made of webband with woven rubber (14 mm wide). The cords ends are attached to the girth with the aid of two snap hooks. If the girth does not have a fastening ring, the supplied leather loop loop with D-ring can be used. The drawrein is equipped with shiny, silver-colored haberdashery of chrome-plated brass. A drawrein is used to obtain a correct head position. If the horse is holding the head too high, the drawrein will act and give pressure to the bit. If the horse follows, the pressure will decrease.

De Drawrein is equipped with:

  • Nylon cord (8 mm wide);
  • Webband with woven rubber (14 mm wide);
  • 2 musketon hooks;
  • Leather single loop with D-ring;
  • Shiny silver-toned haberdashery from chrome-plated brass.


De Drawrein is available in:

  • Various colors.

De Drawrein is suitable for:

  • Horse;
  • Cob.


De Drawrein is made of:

  • Leather


Extra Information:

  • Size Cob: 0.95 m bridle + 1.125 m rope = 2.075 m (4.15 m total length);
  • Size Full: 1.3 m bridle + 1.2 m cord = 2.5 m (5 m total length).
Write Your Own Review
You're reviewing:BR Drawrein Blackpool
Your Rating

Maintenance of your leather halters and bridles

when you have purchased a new leather bridle or halter, it can still be a bit stiff. Many people therefore start greasing right away but you should NOT do this. A new leather halter is the leather untreated and the leather pores are still open. When you use leather grease, lubricate it properly and ensure that it stays stiff. The right way is to first treat your leather halter or bridle with leather oil. It is best to leave your bridle or halter in a container of oil for a night, but that will cost you a lot of oil. The other way is to oil your bridle or halter with a brush. Make sure you touch all the spots and pull the oil in well. Let this take a night. The next morning you can brush the bridle or halter with a dry (tea) clothe. If you have cleaned the bridle or halter, grease it with leather grease. This way you close the leather pores while the oil is still in it. This way your halter or bridle will remain beautiful and supple for a long time. 

With leather bridles and halters, you should clean and take care at least once a month with regular use. When you drive a lot in the open air and also during intensive use we advise you to do this more often. The proper maintenance of the leather ensures that the product lasts longer. Alternation of leather grease and oil is recommended. 

Step 1

Release all the closures and disassemble the entire halter or bridle. Use a dry cloth or brush (do not use a brush with very hard hair) to remove any sand or larger pieces of dirt.

Step 2

Choose a suitable leather soap (or spray) and clean all loose parts well. Do not use too much water because this can make the leather stiff and this is not good for the stitching. After this step let the leather dry well, this goes best at room temperature.

Step 3

Now that the leather is dry, you can get started with leather balm, grease or a conditioner. Use grease during normal maintenance. When the leather is very dry you can use the best oil. Rub the product well with a soft cloth (use a brush with oil). The end result will be better if you rub it in well.

Step 4

Then allow it to penetrate well and spread it with a clean dry cloth. Take care that this cloth does not fluff. When you are done with this and the care product is completely absorbed in the leather, you can reassemble the halter or bridle.

Tips:

  • Store leather products in a well-ventilated and dry room. It is not bad when it gets cold, this can not hurt for leather.
  • Do not give bacteria the chance to damage the leather by cleaning your bridle (sweat residue) and the bit (foam residue) after use.
  • If you treat your bridle one day before use, give the maintenance product sufficient time to withdraw.
  • For a new leather product, first treat with leather oil and then with leather grease, otherwise you lubricate the leather pores and both agents can not properly handle the leather.
  • Only use leather care products for real leather. Artificial leather, patent leather and leather with a plastic layer can thus be damaged.
  • When a leather product is decorated with stones, you should only take this part with a damp cloth.